Electrical Characterization of Individual Cesium Lead Halide Perovskite Nanowires Using Conductive AFM

Perovskite nanostructures have attracted much attention in recent years due to their suitability for a variety of applications such as photovoltaics, light-emitting diodes (LEDs), nanometer-size lasing, and more. These uses rely on the conductive properties of these nanostructures. However, electrical characterization of individual, thin perovskite nanowires has not yet been reported. Here, conductive atomic force microscopy characterization of individual cesium lead halide nanowires is presented. Clear differences are observed in the conductivity of nanowires containing only bromide and nanowires containing a mixture of bromide and iodide. The differences are attributed to a higher density of crystalline defects, deeper trap states, and higher inherent conductivity for nanowires with mixed bromide–iodide content.     

High performance multi-layer varistor (MLV) from doped ZnO nanopowders by water based tape casting: Rheology,sintering, microstructure and properties

In this work, we report the fabrication of a high performance multi-layer varistor (MLV) via water based tape casting method using novel compositions of nanomaterials. Bi₂O₃, CaO and Co₃O₄ doped ZnO nanopowders were prepared by solution combustion synthesis (SCS) route, calcined at different temperatures (550, 650, 750 and 850?°C) and characterized by TEM, XRD, SEM and AFM. The nanopowder (crystallite size ~30?nm) calcined at 650?°C for 1?h was used as the starting material for MLV fabrication. Compositions of the slurry containing doped ZnO nanopowders, binder and plasticizer in water solvent were optimized for the fabrication of thick film. The rheological properties of the slurries having different solid loadings were analysed and thick films of various thicknesses (50–500?µm) were prepared by varying the feeding rate of tape casting. The film roughness of 38.3?nm for the thick film made from 40?wt% solid slurry was found to be superior compared to other samples due to the presence of reduced crack and shrinkage. MLV fired at 950?°C for 1.5?h exhibited a coefficient of nonlinearity of 18 and breakdown voltage of 291.5?V that yields superior properties compared to commercial MLVs.     

水射流表面改性对国产Zirlo锆合金包壳管加速腐蚀氧化膜形貌的影响

为进一步提高国产锆合金包壳管性能,提高反应堆安全性,对国产Zirlo锆合金进行水射流冲击强化,研究在高温高压水腐蚀条件下不同冲击压力对样品表面氧化膜的影响,并与未冲击样品进行对比。结果表明,样品表面在不同压力的冲击下耐蚀性差异较大,当冲击压力达到40 MPa时样品表面氧化膜状态较好,相比于未冲击样品氧化膜厚度减少4.3%,在10 MPa和20 MPa冲击下则出现腐蚀加速情况。     

改性氧化钛对羟乙基乙二胺水溶液解吸CO2的强化

羟乙基乙二胺（AEE）水溶液的CO₂循环吸收量高（1.2molCO₂/molAEE），吸收速度快，稳定性好，但解吸速度慢、解吸量少（0.8mol CO₂/mol AEE）是限制该技术广泛应用的主要原因。本文通过向AEE水溶液中添加质量分数为0.05%～0.20%的改性氧化钛（TiO₂-MWCNT和TiO₂-OH）强化AEE的解吸能力。CO₂循环吸收（40℃）-解吸（120℃）实验结果表明改性氧化钛的添加比氧化钛强化CO₂解吸效果更好，强化顺序为TiO₂-MWCNT＞TiO₂-OH；其对应的最大解吸速率分别为0.093L/min（质量分数0.15%）和0.083L/min（质量分数0.20%），相对于AEE水溶液，分别提高了32.9%和18.6%；其对应的最大解吸量分别为0.92molCO₂/molAEE（质量分数0.15%）和0.88molCO₂/molAEE（质量分数0.20%），分别提高了12.2%和9.7%；其对应的CO₂循环吸收量分别是0.95molCO₂/molAEE（质量分数0.15%）和0.89molCO₂/molAEE（质量分数0.15%），分别提高了18.75%和11.25%；5次循环吸收解吸实验结果表明改性氧化钛强化CO₂解吸效果稳定，具有较强的化学稳定性。对反应后的改性氧化钛进行XRD、BET、FTIR和SEM表征，结果表明改性氧化钛具有较强的结构稳定性。TiO₂-MWCNT和TiO₂-OH在促进有机胺溶液解吸CO₂方面具有一定的工业应用潜力。     

二层沟槽织构对机床导轨表面润滑特性的影响

通过构建二层沟槽织构模型，仿真研究沟槽织构表面的流体动力效应。结果表明：沟槽容积相同时，与单层沟槽相比，二层沟槽的平均油膜压力可以达到单层沟槽的2.31倍；保持二层沟槽的量纲一总深度[β]1、第一层沟槽量纲一宽度[α]1不变时，随着第二层量纲一深度[β]2的增大，平均油膜压力先增大后减小，[β]2为4.4时，平均油膜压力达到最大值；第二层沟槽的量纲一宽度[α]2从0.25增大到0.45时，沟槽内的旋涡区也随之增大，平均油膜压力逐渐减小。     

镓锗铜萃余液综合利用研究与应用

本文针对镓锗铜综合回收系统产出的萃余液,设计通过中和氧化除杂、锌粉置换除铜镉、有机试剂除钴镍、纯碱法生产碱式碳酸锌、高温煅烧生产活性氧化锌和一步法生产元明粉的生产工艺流程,有效的将镓锗铜萃余液分类分离富集,产出具有价值的富集渣和工业产品,进一步提升综合回收经济效益。     

基于双向流固耦合弹性环式挤压油膜阻尼器建模及动力学特性研究

利用数值方法建立了弹性环式挤压油膜阻尼器(ERSFD)的流固耦合模型,分别利用有限元方法以及有限体积法建立了弹性环和内外油膜的CFD数值模型,并进一步利用分时迭代的弱耦合方法实现了油膜以及弹性环控制方程的耦合求解,获得了内油膜的压力分布特性及弹性环的变形,并进一步识别了油膜和弹性环的动力学特性系数;研究了涡动频率、凸台数目、凸台高度、凸台宽度以及弹性环厚度对阻尼器动力学特性系数的影响。结果表明,弹性环的凸台高度对ERSFD油膜动力学特性系数的影响最为明显,ERSFD油膜阻尼与涡动频率无关。     

考虑结构动态变形的缸套-活塞环润滑建模分析

缸套在燃烧冲击和活塞敲击激励下会产生接近表面粗糙度的动态变形,极有可能影响缸套-活塞环组件间的摩擦润滑过程。为了研究缸套动态变形潜在的影响,将动力学仿真获取的缸套内表面的动态变形经过处理后导入到润滑模型中,同时采用数值积分计算的方式对油液压力应力因子和剪切应力因子进行实时计算求解,使仿真计算更加符合实际情况。通过搭建同时考虑缸套变形与油液剪切特性影响的改进润滑模型,计算得到整个工作循环内活塞环上的最小油膜厚度和摩擦力曲线。结果表明:考虑缸套动态变形后的最小油膜厚度和摩擦力曲线出现了明显的波动,而且考虑缸套动态变形后的摩擦力比未考虑之前出现了明显下降。     

Electrocatalytic activity of LaSr3Fe3O10 and LaSr3Fe3O10-GO towards oxygen reduction reaction in alkaline medium

Oxygen reduction reaction(ORR) plays a critical role in many energy conversion and storage processes.Therein, a comparative study of the electrocatalytic activity for ORR in 0.1 mol/L KOH solution was conducted using layered perovskite-like LaSr_3 Fe_3 O_(10) and LaSr3 Fe_3 O_(10)-graphene oxide(GO) composite as electrodes. Linear sweep voltammetry(LSV) results show that the LaSr3 Fe_3 O_(10)-GO hybrid exhibits higher current density, a more positive onset potential(-0.15 V vs. Hg/HgO) in comparison with LaSr_3 Fe_3 O_(10).The value of the overall transferred electrons for both catalysts implies a dominant two electron process for ORR. Both catalysts under alkalic conditions exhibit a two-step Tafel slope, suggesting a change in the reaction mechanism for ORR. The composite electrode exhibits a higher ORR current density, but inferior durability performances in relative to the LaSr_3 Fe_3 O_(10) electrode.